30 venkel corp 4807 spicewood springs road building no. 3 austin, tx 78759 phone: 512 / 794-0081 fax: 512 / 794-0087 toll free: 800 / 950-8365 e-mail: sales@venkel.com www.venkel.com chip resistors specifications features ? flat chip resistors for surface mount applications. ? excellent mechanical strength and electrical stability due to special electrode construction. ? free from troubles at placement due to accurate and uniform physical dimensions. l w t c c c c % of rated power ambient temp. deg. centigrade derating curve 120 100 80 60 40 20 0 30 50 70 90 110 130 150 170 environmental seal thick film resistor element alumina ceramic substrate thick film electrode nickel, tinned outer electrode structure operating temp. range is -55c to +175c ? dc resistance value of zero ohm is 50m ohms max. power max. zero (ohm) resistance l (length) w (width) t (thickness) c (end band) series rating working current range inches inches inches inches at 70c voltage rating (mm) (mm) (mm) (mm) cr0201-20w 0.050w 25v 0.5a 10 - 1m ohms 0.024 .002 0.012 .001 0.010 .002 0.006 .002 (0.6 0.05) (0.3 0.02) (0.25 0.05) (0.15 0.05) cr0402-16w 0.063w 50v 1a zero - 10m ohms 0.040 .002 0.020 .001 0.014 .002 0.008 .004 (1.0 0.05) (0.5 0.02) (0.35 .05) (0.2 0.1) cr0603-16w 0.063w 50v 1a zero - 20m ohms 0.063 .004 0.031 .004 0.018 .004 0.012 .006 (1.6 0.1) (0.8 0.1) (0.45 0.1) (0.30 0.15) cr0603-10w 0.10w 50v 1a zero - 20m ohms 0.063 .004 0.031 .004 0.018 .004 0.012 .006 (1.6 0.1) (0.8 0.1) (0.45 0.1) (0.30 0.15) cr0805-10w 0.10w 150v 2a zero - 22m ohms 0.079 .006 0.050 .006 0.018 .006 0.014 .006 (2.0 0.15) (1.25 0.15) (0.45 0.15) (0.35 0.15) cr0805-8w 0.125w 150v 2a zero - 22m ohms 0.079 .006 0.050 .006 0.018 .006 0.014 .006 (2.0 0.15) (1.25 0.15) (0.45 0.15) (0.35 0.15) cr1206-8w 0.125w 200v 2a zero - 22m ohms 0.126 .006 0.063 .006 0.022 .006 0.020 .008 (3.2 0.15) (1.6 0.15) (0.56 0.15) (0.50 0.20) cr1206-4w 0.25w 200v 2a zero - 22m ohms 0.126 .006 0.063 .006 0.022 .006 0.020 .008 (3.2 0.15) (1.6 0.15) (0.56 0.15) (0.50 0.20) cr1210-4w 0.25w 200v 4a zero - 3.3m ohms 0.126 .006 0.098 .006 0.022 .006 0.020 .008 (3.2 0.15) (2.50 0.15) (0.56 0.15) (0.50 0.20) cr1210-2w 0.50w 200v 4a zero - 3.3m ohms 0.126 .006 0.098 .006 0.022 .006 0.024 .008 (3.2 0.15) (2.50 0.15) (0.56 0.15) (0.60 0.20) cr2010-2w 0.50w 200v 5a zero - 2.2m ohms 0.197 .006 0.098 .006 0.022 .006 0.024 .008 (5.0 0.15) (2.50 0.15) (0.56 0.15) (0.60 0.20) cr2010-1w 1.00w 200v 5a zero - 2.2m ohms 0.197 .006 0.098 .006 0.022 .006 0.024 .008 (5.0 0.15) (2.50 0.15) (0.56 0.15) (0.60 0.20) cr2512-1w 1.00w 200v 5a zero - 2.2m ohms 0.248 .006 0.126 .006 0.022 .006 0.024 .008 (6.3 0.15) (3.2 0.15) (0.56 0.15) (0.60 0.20) cr2512-2w 2.00w 200v 5a zero - 2.2m ohms 0.248 .006 0.126 .006 0.022 .006 0.024 .008 (6.3 0.15) (3.2 0.15) (0.56 0.15) (0.60 0.20)
venkel corp 4807 spicewood springs road building no. 3 austin, tx 78759 phone: 512 / 794-0081 fax: 512 / 794-0087 toll free: 800 / 950-8365 e-mail: sales@venkel.com www.venkel.com 31 3 digit (g&j tol.) jumper 3 zero? e24 series e.g. 2r2=2.2 103=10k 4 digit (f tol.) e96 series e.g. 10r2=10.2 1002=10k 103=10k 103 packaging b: bulk t: tape add only if 13" reel required t cr1206-8w series g tolerance at 25 c f: 1% g: 2% j: 5% for palladium silver termination add (p) above (p): pdag termination 13 how to order characteristics item test basis: eia j-rc-2690a specification requirements typical short-time overload 2.5 x rated voltage for 5 sec. 1% + 0.5 , no arc evidence within 0.4% load life 70c, rated voltage for 1.5 hrs. <1 meg. 3% + 0.1 , > 1 meg. 5% on/0.5 hr. for 1000 hrs. dielectric withstanding voltage 500v for 1 minute no insulation breakdown above 900-950v resistance to soldering heat 270c for 10 seconds 1% + 0.05 , no mechanical damage temperature cycling eia std. 575, para. 3.5 1.0% -55 ~ +125 c, 5 cycles. solderability 230c, 3 seconds, flux applied 95% minimum coverage more than 97-98% curing heat resistance +150c for 10 minutes 1% + 0.05 within 0.3% dry heat resistance -125c for 1,000 hours 3% + 0.1 , no mechanical damage within 0.5% pull terminal strength 500g load for 30 seconds 1% + 0.05 , no mechanical damage within 0.2% pcb terminal strength 1/45mm bend for 10 seconds 1% + 0.05 , no mechanical damage within 0.2% moisture resistance, -55c to +125c, 5 cycles 1% + 0.05 , no mechanical damage within 0.2% thermal shock moisture load life 40c, 95% r.h., 1.5 hr. on, <1 meg 3% + 0.1 , > 1 meg. 5% 0.5 hr. off, 1,000 hours insulation resistance 500v, 1 minute 1,000 meg. minimum more than 10 meg. voltage coefficient rated voltage and + 0/-100ppm/v: above 1k within - 90ppm/v 1/10 times rated voltage low temperature exposure -55c for 1,000 hours 3% + 0.1 , no mechanical damage within 0.5% temp. coefficient ( ppm / c ) j tol.: 200; f tol.: 100 under 10 ohm & over 1 meg ohm, f tol.: 350 0201 and 0402 case sizes, the t.c.r. is 250 for j and f tol.
|